搜索结果 5:

  • MT12 Surface Radio Controller

    The RadioMaster MT12 is a pioneering open-source surfac…

  • SpeedyBee BLS 60A 30×30 4-in-1 ESC

    Specifications
    Product Name SpeedyBee BLS 60A 30×30 4-in-1 ESC
    Firmware BLHeli_S J-H-50
    PC Configurator Download Link https://esc-configurator.com/
    Continuous Current 60A * 4
    Burst Current 80A(10 sec)
    TVS Protective diode Yes
    External Capacitor 1000uF Low ESR Capacitor(In the package)
    ESC Protocol DSHOT300/600
    Power Input 3-6S LiPo
    Power Output VBAT
    Current Sensor Support (Scale=400 Offset=0)
    ESC Telemetry Not supported
    Mounting 30.5 x 30.5mm( 4mm hole diameter)
    Dimension 45.6(L) * 44(W) *8mm(H)
    Weight 23.5g
  • SpeedyBee F405 V3 BLS 60A 30×30 FC&ESC Stack

    Specifications
    Product Name SpeedyBee F405 V3 30×30 Flight Controller
    MCU STM32F405
    IMU(Gyro) BMI270
    USB Port Type Type-C
    Barometer Built-in
    OSD Chip AT7456E chip
    BLE Bluetooth Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
    WIFI Not supported
    DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.
    6-pin DJI Air Unit Plug Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
    Blackbox MicroSD Card Slot *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC), so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the card MUST be formatted with the FAT16 or FAT32 (recommended) filesystems. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose ‘Overwrite format’ then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
    BetaFlight Camera Control Pad Yes(CC pad on the front side)
    Current Sensor Input Supported. For SpeedyBee BLS 60A ESC, please set scale = 400 and Offset = 0.
    Power Input 3S – 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
    5V Output 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 2A.
    9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 2A.
    3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
    4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
    ESC Signal M1 – M4 on bottom side and M5-M8 on front side.
    UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5(Dedicated for ESC telemetry),UART6
    ESC Telemetry UART R5
    I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
    Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
    Buzzer BZ+ and BZ- pad used for 5V Buzzer
    BOOT Button Supported.
    [A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
    [B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
    RSSI Input Supported. Named as RS on the front side.
    Smart Port / F.Port Not supported
    Supported Flight Controller Firmware BetaFlight(Default), INAV (INAV firmware can only use Multishot (recommended) and OneShot125. Please note that DShot is not supported.)
    Firmware Target Name SPEEDYBEEF405V3
    Mounting 30.5 x 30.5mm( 4mm hole diameter)
    Dimension 41.6(L) x 39.4(W) x 7.8(H)mm
    Weight 9.6g
    Product Name SpeedyBee BLS 60A 30×30 4-in-1 ESC
    Firmware BLHeli_S J-H-50
    PC Configurator Download Link https://esc-configurator.com/
    Continuous Current 60A * 4
    Burst Current 80A(10 sec)
    TVS Protective diode Yes
    External Capacitor 1000uF Low ESR Capacitor(In the package)
    ESC Protocol DSHOT300/600
    Power Input 3-6S LiPo
    Power Output VBAT
    Current Sensor Support (Scale=400 Offset=0)
    ESC Telemetry Not supported
    Mounting 30.5 x 30.5mm( 4mm hole diameter)
    Dimension 45.6(L) * 44(W) *8mm(H)
    Weight 23.5g
  • SpeedyBee F405 WING MINI Fixed Wing Flight Controller

    Specifications
    Product Name SpeedyBee F405 WING MINI FC board
    MCU STM32F405, 168MHz, 1MB Flash
    IMU(Gyro&Accelerometer) ICM-42688-P
    Barometer SPL006-001
    OSD Chip AT7456E
    Blackbox MicroSD Card Slot
    UART 6 sets (USART1, USART2, USART3, UART4, UART5,
    UART6 – Dedicated for Wireless board Telemetry connection)
    I2C 1x Used for magnetometer, digital airspeed sensor
    ADC 4x (VBAT, Current, Analog RSSI, Analog AirSpeed)
    PWM 12x (9x pin headers + 2x solder pads + 1x “LED” pad)
    ELRS/CRSF Receiver Supported, connected to UART1
    SBUS Built-in inverter for SBUS input (UART2-RX)
    LED 3x LEDs for FC STATUS (Blue, Green) and 3.3V indicator (Red)
    Analog RSSI Supported, Named as “RS”
    Dual Analog Camera Switching Default to Camera1 Video Input (C1). Switch between C1 and C2 using ArduPilot Relay or INAV Modes/USER.
    Both cameras should have the same video format, either PAL or NTSC.
    Supported FC Firmware INAV: SpeedyBeeF405WING (default)
    ArduPilot: SpeedyBeeF405WING
    Weight 5.6g
    Product Name SpeedyBee F405 WING MINI PDB board
    Input voltage range 7~26V (2~6S LiPo)
    Battery Voltage Sensor Connect to FC board VBAT, 1K:10K (Scale 1100 in INAV, BATT_VOLT_MULT 11.0 in ArduPilot)
    Battery Current Sensor 80A continuous, 150A peak Connect to FC board Current (Scale 195 in INAV, 50 A/V in ArduPilot)
    TVS Protective diode Yes
    FC BEC output Output 5.2V +/- 0.1V DC Continuous current 2 Amps, 3A Peak Designed for FC, Receiver, GPS module, AirSpeed Sensor, Telemetry module
    VTX & Camera power supply The VTX power interface Vv offers two power supply options: direct battery voltage or integrated BEC 5V (sharing the 5V4A Servo BEC voltage)
    By default, it is set to battery voltage
    (Ensure the VTX and camera input voltage range is compatible)
    Switching to 5V power supply is possible via pad jumper (using Servo BEC output)
    (If using this method, ensure the current requirements for both servo and VTX are sufficient)
    Servo BEC output Output 5V +/- 0.1V DC Continuous current 4 Amps, 5A Peak Voltage adjustable, 5V Default, 6V via jumper Designed for Servos.
    Weight 5.5g
    Product Name SpeedyBee F405 WING MINI Wireless USB Extender
    Wireless Configuration (long press BOOT button for 6 seconds to switch modes)
    INAV:Please make sure the MSP switch on UART 6 is turned on and set to a baud rate of 115200 ArduPilot:Please make sure the Serial 6 is set to baud rate 115200 and protocol Mavlink2
    BLE mode, connect to Speedybee APP
    Wi-Fi (AP)mode, able to connect to Speedybee APP, QGroundControl APP, MissionPlanner, etc. WiFi: Speedybee eFLY-WIFI Password: 88888888
    Wi-Fi (STA)mode, able to connect to QGroundControl APP, MissionPlanner, etc.
    Step 1: turn on Personal Hotspot;
    Step 2: Set hotspot, locate NAME/Device Name/Hotspot name/etc.
    Step 3: change the current name to eFLY and the password is, 88888888
    Wireless off mode
    USB Port Type Type-C
    Buzzer 5V Active Buzzer
    Weight 3.2g
  • SpeedyBee F7 V2 BL32 45A Stack(with V22 ESC)

    SpeedyBee F7V2 Specifications
    MCU STM32F722
    IMU MPU6000
    USB Type-C
    Barometer BMP280 (I2C) Warning:Do not apply conformal coating on the berometer because the air hole can be clogged.
    OSD BetaFlight OSD w/ AT7456E chip
    BLE Support, used for Flight Controller configuration
    WiFi Support, used for data transfer, e.g firmware
    flashing, and Blackbox analysis.
    DJI Air Unit slot A full DJI Air Unit JST slot onboard
    BlackBox 16MB onboard dataflash
    Current Sensor 1 : 10 (Scale 168)
    BetaFlight Camera Control Pad Yes
    Power input 3-6S
    5V BEC x 1 5V output x 7 , 6 pads, and a BZ+ pad used for Buzzer, the maximum load current in total is 2.5A.
    9V BEC x 1 9V output x 2 , 1 pad and another one used for DJI slot, the maximum load current in total is 2.5A.
    4.5V power output 1 * 4.5V output pad
    3.3V power output 1 * 3.3V output pad, the maximum load current is 500mA.
    ESC signal M1 – M4
    UART Full UART * 5(UART1, UART2, UART3, UART5, UART6)
    ESC Telemetry UART UART4 RX
    I2C Used for external Magnetometer, Sonar, etc.
    LED pin Used for WS2812 LED
    Buzzer BZ+ and BZ- pad used for 5V Buzzer
    Boot button Used to easy enter DFU mode
    RSSI input RSSI input solder pad
    SmartPort Use any TX pad of UART for the SmartPort feature.
    Support Flight Controller Firmware BetaFlight(Default), EMUFlight
    Target name SPEEDYBEEF7V2
    Mounting 30.5 x 30.5mm,  4mm hole size
    Dimension 41 x 38 x 6.9mm
    Weight 9g
    SpeedyBee BLHeli32 45A 4 in 1 ESC Specifications
    Firmware BLHeli32 SpeedyBee 4in1
    Continuous Current 45A * 4
    Burst Current 55A(10S)
    ESC Protocol DSHOT300/600/1200
    Power input 3-6S Note: Strongly recommended to solder the filtering capacitor between VBAT”+” and” -“
    Power output VBAT
    Current Sensor Support (Scale 168)
    ESC Telemetry Support
    Mounting 30.5 x 30.5mm, 4mm hole size
    Dimension 41 * 45 * 6.5mm
    Weight 12.5g
    Supported Motor 1900KV or below should be needed for 6S